diff --git a/base.mk b/base.mk index dc446c1..3b48415 100644 --- a/base.mk +++ b/base.mk @@ -47,6 +47,7 @@ PRODUCT_COPY_FILES += \ # vendor/etc PRODUCT_COPY_FILES += \ device/phh/treble/nfc/libnfc-nci.conf:system/phh/libnfc-nci-oreo.conf + device/phh/treble/nfc/libnfc-nci-huawei.conf:system/phh/libnfc-nci-huawei.conf # LineageOS build may need this to make NFC work PRODUCT_PACKAGES += \ diff --git a/nfc/libnfc-nci-huawei.conf b/nfc/libnfc-nci-huawei.conf new file mode 100644 index 0000000..a5487b8 --- /dev/null +++ b/nfc/libnfc-nci-huawei.conf @@ -0,0 +1,394 @@ +# This file from Honor View 10 stock pie, thanks @haky86 +###################### Start of libnfc-common.conf ####################### + +############################################################################### +# Application options +APPL_TRACE_LEVEL=0x02 +PROTOCOL_TRACE_LEVEL=0xFFFFFFFF + +############################################################################### +# performance measurement +# Change this setting to control how often USERIAL log the performance (throughput) +# data on read/write/poll +# defailt is to log performance dara for every 100 read or write +#REPORT_PERFORMANCE_MEASURE=100 + +############################################################################### +# File used for NFA storage +NFA_STORAGE="/data/nfc" + +############################################################################### +# Snooze Mode Settings +# +# By default snooze mode is enabled. Set SNOOZE_MODE_CFG byte[0] to 0 +# to disable. +# +# If SNOOZE_MODE_CFG is not provided, the default settings are used: +# They are as follows: +# 8 Sleep Mode (0=Disabled 1=UART 8=SPI/I2C) +# 0 Idle Threshold Host +# 0 Idle Threshold HC +# 0 NFC Wake active mode (0=ActiveLow 1=ActiveHigh) +# 1 Host Wake active mode (0=ActiveLow 1=ActiveHigh) +# +#SNOOZE_MODE_CFG={08:00:00:00:01} + +############################################################################### +# Insert a delay in milliseconds after NFC_WAKE and before write to NFCC +#NFC_WAKE_DELAY=20 + +############################################################################### +# Various Delay settings (in ms) used in USERIAL +# POWER_ON_DELAY +# Delay after turning on chip, before writing to transport (default 300) +# PRE_POWER_OFF_DELAY +# Delay after deasserting NFC-Wake before turn off chip (default 0) +# POST_POWER_OFF_DELAY +# Delay after turning off chip, before USERIAL_close returns (default 0) +# +#POWER_ON_DELAY=300 +#PRE_POWER_OFF_DELAY=0 +#POST_POWER_OFF_DELAY=0 + +############################################################################### +# Maximum time (ms) to wait for RESET NTF after setting REG_PU to high +# The default is 1000. +#NFCC_ENABLE_TIMEOUT=0 + +############################################################################### +# LPTD mode configuration +# byte[0] is the length of the remaining bytes in this value +# if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled). +# byte[1] is the param id it should be set to B9. +# byte[2] is the length of the LPTD parameters +# byte[3] indicates if LPTD is enabled +# if set to 0, LPTD will be disabled (parameters will still be sent). +# byte[4-n] are the LPTD parameters. +# By default, LPTD is enabled and default settings are used. +# See nfc_hal_dm_cfg.c for defaults +#LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00} + +############################################################################### +# Startup Configuration (100 bytes maximum) +# +# For the 0xCA parameter, byte[9] (marked by 'AA') is for UICC0, and byte[10] (marked by BB) is +# for UICC1. The values are defined as: +# 0 : UICCx only supports ISO_DEP in low power mode. +# 2 : UICCx only supports Mifare in low power mode. +# 3 : UICCx supports both ISO_DEP and Mifare in low power mode. +# +# AA BB +#NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:80:01:01} + +############################################################################### +# Startup Vendor Specific Configuration (100 bytes maximum); +# byte[0] TLV total len = 0x5 +# byte[1] NCI_MTS_CMD|NCI_GID_PROP = 0x2f +# byte[2] NCI_MSG_FRAME_LOG = 0x9 +# byte[3] 2 +# byte[4] 0=turn off RF frame logging; 1=turn on +# byte[5] 0=turn off SWP frame logging; 1=turn on +# NFA_DM_START_UP_VSC_CFG={05:2F:09:02:01:01} + +############################################################################### +# Antenna Configuration - This data is used when setting 0xC8 config item +# at startup (before discovery is started). If not used, no value is sent. +# +# The settings for this value are documented here: +# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/ +# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx +# This document is maintained by Paul Forshaw. +# +# The values marked as ?? should be tweaked per antenna or customer/app: +# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04} +# array[0] = 0x20 is length of the payload from array[1] to the end +# array[1] = 0xC8 is PREINIT_DSP_CFG +#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04} + +############################################################################### +# Configure crystal frequency when internal LPO can't detect the frequency. +#XTAL_FREQUENCY=0 +############################################################################### +# Configure the default Destination Gate used by HCI (the default is 4, which +# is the ETSI loopback gate. +NFA_HCI_DEFAULT_DEST_GATE=0xF0 + +############################################################################### +# Configure the single default SE to use. The default is to use the first +# SE that is detected by the stack. This value might be used when the phone +# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use +# one of them (e.g. 0xF4). +#ACTIVE_SE=0xF3 + +############################################################################### +# Configure the default NfcA/IsoDep techology and protocol route. Can be +# either a secure element (e.g. 0xF4) or the host (0x00) +#DEFAULT_ISODEP_ROUTE=0x00 + +############################################################################### +# Configure the NFC Extras to open and use a static pipe. If the value is +# not set or set to 0, then the default is use a dynamic pipe based on a +# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value +# for each UICC (where F3="UICC0" and F4="UICC1") +#NFA_HCI_STATIC_PIPE_ID_F3=0x70 +#NFA_HCI_STATIC_PIPE_ID_01=0x19 +NFA_HCI_STATIC_PIPE_ID_C0=0x19 +NFA_HCI_STATIC_PIPE_ID_02=0x20 +############################################################################### +# When disconnecting from Oberthur secure element, perform a warm-reset of +# the secure element to deselect the applet. +# The default hex value of the command is 0x3. If this variable is undefined, +# then this feature is not used. +#OBERTHUR_WARM_RESET_COMMAND=0x03 + +############################################################################### +# Force UICC to only listen to the following technology(s). +# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. +# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F +UICC_LISTEN_TECH_MASK=0x07 + +############################################################################### +# Forcing HOST to listen for a selected protocol +# 0x00 : Disable Host Listen +# 0x01 : Enable Host to Listen (A) for ISO-DEP tech A +# 0x02 : Enable Host to Listen (B) for ISO-DEP tech B +# 0x04 : Enable Host to Listen (F) for T3T Tag Type Protocol tech F +# 0x07 : Enable Host to Listen (ABF)for ISO-DEP tech AB & T3T Tag Type Protocol tech F +HOST_LISTEN_TECH_MASK=0x07 + +############################################################################### +# Enabling/Disabling Forward functionality +# Disable 0x00 +# Enable 0x01 +NXP_FWD_FUNCTIONALITY_ENABLE=0x00 + +############################################################################### +# Allow UICC to be powered off if there is no traffic. +# Timeout is in ms. If set to 0, then UICC will not be powered off. +#UICC_IDLE_TIMEOUT=30000 +UICC_IDLE_TIMEOUT=0 + +############################################################################### +# AID for Empty Select command +# If specified, this AID will be substituted when an Empty SELECT command is +# detected. The first byte is the length of the AID. Maximum length is 16. +AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00} +############################################################################### +# Maximum Number of Credits to be allowed by the NFCC +# This value overrides what the NFCC specifices allowing the host to have +# the control to work-around transport limitations. If this value does +# not exist or is set to 0, the NFCC will provide the number of credits. +MAX_RF_DATA_CREDITS=1 + +############################################################################### +# This setting allows you to disable registering the T4t Virtual SE that causes +# the NFCC to send PPSE requests to the DH. +# The default setting is enabled (i.e. T4t Virtual SE is registered). +#REGISTER_VIRTUAL_SE=1 + +############################################################################### +# When screen is turned off, specify the desired power state of the controller. +# 0: power-off-sleep state; DEFAULT +# 1: full-power state +# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used) +SCREEN_OFF_POWER_STATE=1 + +############################################################################### +# Firmware patch file +# If the value is not set then patch download is disabled. +#FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd" + +############################################################################### +# Firmware pre-patch file (sent before the above patch file) +# If the value is not set then pre-patch is not used. +#FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd" + +############################################################################### +# Firmware patch format +# 1 = HCD +# 2 = NCD (default) +#NFA_CONFIG_FORMAT=2 + +############################################################################### +# SPD Debug mode +# If set to 1, any failure of downloading a patch will trigger a hard-stop +#SPD_DEBUG=0 + +############################################################################### +# SPD Max Retry Count +# The number of attempts to download a patch before giving up (defualt is 3). +# Note, this resets after a power-cycle. +#SPD_MAX_RETRY_COUNT=3 + +############################################################################### +# transport driver +# +# TRANSPORT_DRIVER= +# +# where can be, for example: +# "/dev/ttyS" (UART) +# "/dev/bcmi2cnfc" (I2C) +# "hwtun" (HW Tunnel) +# "/dev/bcmspinfc" (SPI) +# "/dev/btusb0" (BT USB) +#TRANSPORT_DRIVER="/dev/bcm2079x-i2c" + +############################################################################### +# power control driver +# Specify a kernel driver that support ioctl commands to control NFC_EN and +# NFC_WAKE gpio signals. +# +# POWER_CONTRL_DRIVER= +# where can be, for example: +# "/dev/nfcpower" +# "/dev/bcmi2cnfc" (I2C) +# "/dev/bcmspinfc" (SPI) +# i2c and spi driver may be used to control NFC_EN and NFC_WAKE signal +#POWER_CONTROL_DRIVER="/dev/bcm2079x-i2c" + +############################################################################### +# I2C transport driver options +# Mako does not support 10-bit I2C addresses +# Revert to 7-bit address +#BCMI2CNFC_ADDRESS=0x77 + +############################################################################### +# I2C transport driver try to read multiple packets in read() if data is available +# remove the comment below to enable this feature +#READ_MULTIPLE_PACKETS=1 + +############################################################################### +# SPI transport driver options +#SPI_NEGOTIATION={0A:F0:00:01:00:00:00:FF:FF:00:00} + +############################################################################### +# UART transport driver options +# +# PORT=1,2,3,... +# BAUD=115200, 19200, 9600, 4800, +# DATABITS=8, 7, 6, 5 +# PARITY="even" | "odd" | "none" +# STOPBITS="0" | "1" | "1.5" | "2" + +#UART_PORT=2 +#UART_BAUD=115200 +#UART_DATABITS=8 +#UART_PARITY="none" +#UART_STOPBITS="1" + +############################################################################### +# Insert a delay in microseconds per byte after a write to NFCC. +# after writing a block of data to the NFCC, delay this an amopunt of time before +# writing next block of data. the delay is calculated as below +# NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds +# e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write +#NFC_WRITE_DELAY=20 + +############################################################################### +# Maximum Number of Credits to be allowed by the NFCC +# This value overrides what the NFCC specifices allowing the host to have +# the control to work-around transport limitations. If this value does +# not exist or is set to 0, the NFCC will provide the number of credits. +#MAX_RF_DATA_CREDITS=1 + +############################################################################### +# Default poll duration (in ms) +# The defualt is 500ms if not set (see nfc_target.h) +#NFA_DM_DISC_DURATION_POLL=333 +############################################################################### +# Antenna Configuration - This data is used when setting 0xC8 config item +# at startup (before discovery is started). If not used, no value is sent. +# +# The settings for this value are documented here: +# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/ +# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx +# This document is maintained by Paul Forshaw. +# +# The values marked as ?? should be tweaked per antenna or customer/app: +# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04} +# array[0] = 0x20 is length of the payload from array[1] to the end +# array[1] = 0xC8 is PREINIT_DSP_CFG +#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04} + + +############################################################################### +# Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1. +# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm +# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block +# 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate +# 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0 +# 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3 +#PRESENCE_CHECK_ALGORITHM=0 + +############################################################################### +# Force tag polling for the following technology(s). +# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. +# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | +# NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 | +# NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO | +# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE. +# +# Notable bits: +# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ +# NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B */ +# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ +# NFA_TECHNOLOGY_MASK_ISO15693 0x08 /* Proprietary Technology */ +# NFA_TECHNOLOGY_MASK_KOVIO 0x20 /* Proprietary Technology */ +# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */ +# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */ +POLLING_TECH_MASK=0xEF + +############################################################################### +# Force P2P to only listen for the following technology(s). +# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h. +# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F | +# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE +# +# Notable bits: +# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */ +# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */ +# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */ +# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */ +P2P_LISTEN_TECH_MASK=0xC4 + +PRESERVE_STORAGE=0x01 + +############################################################################### +# NCI Hal Module name +NCI_HAL_MODULE="nfc_nci.pn54x" + +############################################################################## +# Deactivate notification wait time out in seconds used in ETSI Reader mode +# 0 - Infinite wait +NFA_DM_DISC_NTF_TIMEOUT=100 + +############################################################################### +# AID_MATCHING constants +# AID_MATCHING_EXACT_ONLY 0x00 +# AID_MATCHING_EXACT_OR_PREFIX 0x01 +# AID_MATCHING_PREFIX_ONLY 0x02 +AID_MATCHING_MODE=0x01 + +############################################################################### +# Default Secure Element route id +DEFAULT_OFFHOST_ROUTE=0x02 + +############################################################################### +# Vendor Specific Proprietary Protocol & Discovery Configuration +# Set to 0xFF if unsupported +# byte[0] NCI_PROTOCOL_18092_ACTIVE +# byte[1] NCI_PROTOCOL_B_PRIME +# byte[2] NCI_PROTOCOL_DUAL +# byte[3] NCI_PROTOCOL_15693 +# byte[4] NCI_PROTOCOL_KOVIO +# byte[5] NCI_PROTOCOL_MIFARE +# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO +# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME +# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME +NFA_PROPRIETARY_CFG={05:FF:FF:06:81:80:70:FF:FF} + +################################################################################# +# Bail out mode +# If set to 1, NFCC is using bail out mode for either Type A or Type B poll. +NFA_POLL_BAIL_OUT_MODE=0x01 +################################################################################# diff --git a/rw-system.sh b/rw-system.sh index 88f0316..a88e500 100644 --- a/rw-system.sh +++ b/rw-system.sh @@ -229,6 +229,18 @@ if getprop ro.product.model |grep -qF ANE;then setprop debug.sf.latch_unsignaled 1 fi +if getprop ro.vendor.build.fingerprint |grep -iq -E -e 'huawei|honor' || getprop persist.sys.overlay.huawei |grep -iq -E -e 'true' ; then + p=/product/etc/nfc/libnfc_nxp_*_*.conf + mount -o bind "$p" /system/etc/libnfc-nxp.conf || \ + mount -o bind /product/etc/libnfc-nxp.conf /system/etc/libnfc-nxp.conf || true + + p=/product/etc/nfc/libnfc_brcm_*_*.conf + mount -o bind "$p" /system/etc/libnfc-brcm.conf || \ + mount -o bind /product/etc/libnfc-nxp.conf /system/etc/libnfc-nxp.conf || true + + mount -o bind /system/phh/libnfc-nci-huawei.conf /system/etc/libnfc-nci.conf +fi + if getprop ro.vendor.build.fingerprint | grep -qE -e ".*(crown|star)[q2]*lte.*" -e ".*(SC-0[23]K|SCV3[89]).*";then for f in /vendor/lib/libfloatingfeature.so /vendor/lib64/libfloatingfeature.so;do [ ! -f $f ] && continue