395 lines
18 KiB
Plaintext
395 lines
18 KiB
Plaintext
|
# This file from Honor View 10 stock pie, thanks @haky86
|
||
|
|
###################### Start of libnfc-common.conf #######################
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Application options
|
||
|
|
APPL_TRACE_LEVEL=0x02
|
||
|
|
PROTOCOL_TRACE_LEVEL=0xFFFFFFFF
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# performance measurement
|
||
|
|
# Change this setting to control how often USERIAL log the performance (throughput)
|
||
|
|
# data on read/write/poll
|
||
|
|
# defailt is to log performance dara for every 100 read or write
|
||
|
|
#REPORT_PERFORMANCE_MEASURE=100
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# File used for NFA storage
|
||
|
|
NFA_STORAGE="/data/nfc"
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Snooze Mode Settings
|
||
|
|
#
|
||
|
|
# By default snooze mode is enabled. Set SNOOZE_MODE_CFG byte[0] to 0
|
||
|
|
# to disable.
|
||
|
|
#
|
||
|
|
# If SNOOZE_MODE_CFG is not provided, the default settings are used:
|
||
|
|
# They are as follows:
|
||
|
|
# 8 Sleep Mode (0=Disabled 1=UART 8=SPI/I2C)
|
||
|
|
# 0 Idle Threshold Host
|
||
|
|
# 0 Idle Threshold HC
|
||
|
|
# 0 NFC Wake active mode (0=ActiveLow 1=ActiveHigh)
|
||
|
|
# 1 Host Wake active mode (0=ActiveLow 1=ActiveHigh)
|
||
|
|
#
|
||
|
|
#SNOOZE_MODE_CFG={08:00:00:00:01}
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Insert a delay in milliseconds after NFC_WAKE and before write to NFCC
|
||
|
|
#NFC_WAKE_DELAY=20
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Various Delay settings (in ms) used in USERIAL
|
||
|
|
# POWER_ON_DELAY
|
||
|
|
# Delay after turning on chip, before writing to transport (default 300)
|
||
|
|
# PRE_POWER_OFF_DELAY
|
||
|
|
# Delay after deasserting NFC-Wake before turn off chip (default 0)
|
||
|
|
# POST_POWER_OFF_DELAY
|
||
|
|
# Delay after turning off chip, before USERIAL_close returns (default 0)
|
||
|
|
#
|
||
|
|
#POWER_ON_DELAY=300
|
||
|
|
#PRE_POWER_OFF_DELAY=0
|
||
|
|
#POST_POWER_OFF_DELAY=0
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Maximum time (ms) to wait for RESET NTF after setting REG_PU to high
|
||
|
|
# The default is 1000.
|
||
|
|
#NFCC_ENABLE_TIMEOUT=0
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# LPTD mode configuration
|
||
|
|
# byte[0] is the length of the remaining bytes in this value
|
||
|
|
# if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled).
|
||
|
|
# byte[1] is the param id it should be set to B9.
|
||
|
|
# byte[2] is the length of the LPTD parameters
|
||
|
|
# byte[3] indicates if LPTD is enabled
|
||
|
|
# if set to 0, LPTD will be disabled (parameters will still be sent).
|
||
|
|
# byte[4-n] are the LPTD parameters.
|
||
|
|
# By default, LPTD is enabled and default settings are used.
|
||
|
|
# See nfc_hal_dm_cfg.c for defaults
|
||
|
|
#LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00}
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Startup Configuration (100 bytes maximum)
|
||
|
|
#
|
||
|
|
# For the 0xCA parameter, byte[9] (marked by 'AA') is for UICC0, and byte[10] (marked by BB) is
|
||
|
|
# for UICC1. The values are defined as:
|
||
|
|
# 0 : UICCx only supports ISO_DEP in low power mode.
|
||
|
|
# 2 : UICCx only supports Mifare in low power mode.
|
||
|
|
# 3 : UICCx supports both ISO_DEP and Mifare in low power mode.
|
||
|
|
#
|
||
|
|
# AA BB
|
||
|
|
#NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:80:01:01}
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Startup Vendor Specific Configuration (100 bytes maximum);
|
||
|
|
# byte[0] TLV total len = 0x5
|
||
|
|
# byte[1] NCI_MTS_CMD|NCI_GID_PROP = 0x2f
|
||
|
|
# byte[2] NCI_MSG_FRAME_LOG = 0x9
|
||
|
|
# byte[3] 2
|
||
|
|
# byte[4] 0=turn off RF frame logging; 1=turn on
|
||
|
|
# byte[5] 0=turn off SWP frame logging; 1=turn on
|
||
|
|
# NFA_DM_START_UP_VSC_CFG={05:2F:09:02:01:01}
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Antenna Configuration - This data is used when setting 0xC8 config item
|
||
|
|
# at startup (before discovery is started). If not used, no value is sent.
|
||
|
|
#
|
||
|
|
# The settings for this value are documented here:
|
||
|
|
# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
|
||
|
|
# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
|
||
|
|
# This document is maintained by Paul Forshaw.
|
||
|
|
#
|
||
|
|
# The values marked as ?? should be tweaked per antenna or customer/app:
|
||
|
|
# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
|
||
|
|
# array[0] = 0x20 is length of the payload from array[1] to the end
|
||
|
|
# array[1] = 0xC8 is PREINIT_DSP_CFG
|
||
|
|
#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04}
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Configure crystal frequency when internal LPO can't detect the frequency.
|
||
|
|
#XTAL_FREQUENCY=0
|
||
|
|
###############################################################################
|
||
|
|
# Configure the default Destination Gate used by HCI (the default is 4, which
|
||
|
|
# is the ETSI loopback gate.
|
||
|
|
NFA_HCI_DEFAULT_DEST_GATE=0xF0
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Configure the single default SE to use. The default is to use the first
|
||
|
|
# SE that is detected by the stack. This value might be used when the phone
|
||
|
|
# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use
|
||
|
|
# one of them (e.g. 0xF4).
|
||
|
|
#ACTIVE_SE=0xF3
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Configure the default NfcA/IsoDep techology and protocol route. Can be
|
||
|
|
# either a secure element (e.g. 0xF4) or the host (0x00)
|
||
|
|
#DEFAULT_ISODEP_ROUTE=0x00
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Configure the NFC Extras to open and use a static pipe. If the value is
|
||
|
|
# not set or set to 0, then the default is use a dynamic pipe based on a
|
||
|
|
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value
|
||
|
|
# for each UICC (where F3="UICC0" and F4="UICC1")
|
||
|
|
#NFA_HCI_STATIC_PIPE_ID_F3=0x70
|
||
|
|
#NFA_HCI_STATIC_PIPE_ID_01=0x19
|
||
|
|
NFA_HCI_STATIC_PIPE_ID_C0=0x19
|
||
|
|
NFA_HCI_STATIC_PIPE_ID_02=0x20
|
||
|
|
###############################################################################
|
||
|
|
# When disconnecting from Oberthur secure element, perform a warm-reset of
|
||
|
|
# the secure element to deselect the applet.
|
||
|
|
# The default hex value of the command is 0x3. If this variable is undefined,
|
||
|
|
# then this feature is not used.
|
||
|
|
#OBERTHUR_WARM_RESET_COMMAND=0x03
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Force UICC to only listen to the following technology(s).
|
||
|
|
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||
|
|
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F
|
||
|
|
UICC_LISTEN_TECH_MASK=0x07
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Forcing HOST to listen for a selected protocol
|
||
|
|
# 0x00 : Disable Host Listen
|
||
|
|
# 0x01 : Enable Host to Listen (A) for ISO-DEP tech A
|
||
|
|
# 0x02 : Enable Host to Listen (B) for ISO-DEP tech B
|
||
|
|
# 0x04 : Enable Host to Listen (F) for T3T Tag Type Protocol tech F
|
||
|
|
# 0x07 : Enable Host to Listen (ABF)for ISO-DEP tech AB & T3T Tag Type Protocol tech F
|
||
|
|
HOST_LISTEN_TECH_MASK=0x07
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Enabling/Disabling Forward functionality
|
||
|
|
# Disable 0x00
|
||
|
|
# Enable 0x01
|
||
|
|
NXP_FWD_FUNCTIONALITY_ENABLE=0x00
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Allow UICC to be powered off if there is no traffic.
|
||
|
|
# Timeout is in ms. If set to 0, then UICC will not be powered off.
|
||
|
|
#UICC_IDLE_TIMEOUT=30000
|
||
|
|
UICC_IDLE_TIMEOUT=0
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# AID for Empty Select command
|
||
|
|
# If specified, this AID will be substituted when an Empty SELECT command is
|
||
|
|
# detected. The first byte is the length of the AID. Maximum length is 16.
|
||
|
|
AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00}
|
||
|
|
###############################################################################
|
||
|
|
# Maximum Number of Credits to be allowed by the NFCC
|
||
|
|
# This value overrides what the NFCC specifices allowing the host to have
|
||
|
|
# the control to work-around transport limitations. If this value does
|
||
|
|
# not exist or is set to 0, the NFCC will provide the number of credits.
|
||
|
|
MAX_RF_DATA_CREDITS=1
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# This setting allows you to disable registering the T4t Virtual SE that causes
|
||
|
|
# the NFCC to send PPSE requests to the DH.
|
||
|
|
# The default setting is enabled (i.e. T4t Virtual SE is registered).
|
||
|
|
#REGISTER_VIRTUAL_SE=1
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# When screen is turned off, specify the desired power state of the controller.
|
||
|
|
# 0: power-off-sleep state; DEFAULT
|
||
|
|
# 1: full-power state
|
||
|
|
# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used)
|
||
|
|
SCREEN_OFF_POWER_STATE=1
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Firmware patch file
|
||
|
|
# If the value is not set then patch download is disabled.
|
||
|
|
#FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd"
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Firmware pre-patch file (sent before the above patch file)
|
||
|
|
# If the value is not set then pre-patch is not used.
|
||
|
|
#FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd"
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Firmware patch format
|
||
|
|
# 1 = HCD
|
||
|
|
# 2 = NCD (default)
|
||
|
|
#NFA_CONFIG_FORMAT=2
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# SPD Debug mode
|
||
|
|
# If set to 1, any failure of downloading a patch will trigger a hard-stop
|
||
|
|
#SPD_DEBUG=0
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# SPD Max Retry Count
|
||
|
|
# The number of attempts to download a patch before giving up (defualt is 3).
|
||
|
|
# Note, this resets after a power-cycle.
|
||
|
|
#SPD_MAX_RETRY_COUNT=3
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# transport driver
|
||
|
|
#
|
||
|
|
# TRANSPORT_DRIVER=<driver>
|
||
|
|
#
|
||
|
|
# where <driver> can be, for example:
|
||
|
|
# "/dev/ttyS" (UART)
|
||
|
|
# "/dev/bcmi2cnfc" (I2C)
|
||
|
|
# "hwtun" (HW Tunnel)
|
||
|
|
# "/dev/bcmspinfc" (SPI)
|
||
|
|
# "/dev/btusb0" (BT USB)
|
||
|
|
#TRANSPORT_DRIVER="/dev/bcm2079x-i2c"
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# power control driver
|
||
|
|
# Specify a kernel driver that support ioctl commands to control NFC_EN and
|
||
|
|
# NFC_WAKE gpio signals.
|
||
|
|
#
|
||
|
|
# POWER_CONTRL_DRIVER=<driver>
|
||
|
|
# where <driver> can be, for example:
|
||
|
|
# "/dev/nfcpower"
|
||
|
|
# "/dev/bcmi2cnfc" (I2C)
|
||
|
|
# "/dev/bcmspinfc" (SPI)
|
||
|
|
# i2c and spi driver may be used to control NFC_EN and NFC_WAKE signal
|
||
|
|
#POWER_CONTROL_DRIVER="/dev/bcm2079x-i2c"
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# I2C transport driver options
|
||
|
|
# Mako does not support 10-bit I2C addresses
|
||
|
|
# Revert to 7-bit address
|
||
|
|
#BCMI2CNFC_ADDRESS=0x77
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# I2C transport driver try to read multiple packets in read() if data is available
|
||
|
|
# remove the comment below to enable this feature
|
||
|
|
#READ_MULTIPLE_PACKETS=1
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# SPI transport driver options
|
||
|
|
#SPI_NEGOTIATION={0A:F0:00:01:00:00:00:FF:FF:00:00}
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# UART transport driver options
|
||
|
|
#
|
||
|
|
# PORT=1,2,3,...
|
||
|
|
# BAUD=115200, 19200, 9600, 4800,
|
||
|
|
# DATABITS=8, 7, 6, 5
|
||
|
|
# PARITY="even" | "odd" | "none"
|
||
|
|
# STOPBITS="0" | "1" | "1.5" | "2"
|
||
|
|
|
||
|
|
#UART_PORT=2
|
||
|
|
#UART_BAUD=115200
|
||
|
|
#UART_DATABITS=8
|
||
|
|
#UART_PARITY="none"
|
||
|
|
#UART_STOPBITS="1"
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Insert a delay in microseconds per byte after a write to NFCC.
|
||
|
|
# after writing a block of data to the NFCC, delay this an amopunt of time before
|
||
|
|
# writing next block of data. the delay is calculated as below
|
||
|
|
# NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds
|
||
|
|
# e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write
|
||
|
|
#NFC_WRITE_DELAY=20
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Maximum Number of Credits to be allowed by the NFCC
|
||
|
|
# This value overrides what the NFCC specifices allowing the host to have
|
||
|
|
# the control to work-around transport limitations. If this value does
|
||
|
|
# not exist or is set to 0, the NFCC will provide the number of credits.
|
||
|
|
#MAX_RF_DATA_CREDITS=1
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Default poll duration (in ms)
|
||
|
|
# The defualt is 500ms if not set (see nfc_target.h)
|
||
|
|
#NFA_DM_DISC_DURATION_POLL=333
|
||
|
|
###############################################################################
|
||
|
|
# Antenna Configuration - This data is used when setting 0xC8 config item
|
||
|
|
# at startup (before discovery is started). If not used, no value is sent.
|
||
|
|
#
|
||
|
|
# The settings for this value are documented here:
|
||
|
|
# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
|
||
|
|
# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
|
||
|
|
# This document is maintained by Paul Forshaw.
|
||
|
|
#
|
||
|
|
# The values marked as ?? should be tweaked per antenna or customer/app:
|
||
|
|
# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
|
||
|
|
# array[0] = 0x20 is length of the payload from array[1] to the end
|
||
|
|
# array[1] = 0xC8 is PREINIT_DSP_CFG
|
||
|
|
#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04}
|
||
|
|
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1.
|
||
|
|
# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
|
||
|
|
# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
|
||
|
|
# 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate
|
||
|
|
# 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0
|
||
|
|
# 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3
|
||
|
|
#PRESENCE_CHECK_ALGORITHM=0
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Force tag polling for the following technology(s).
|
||
|
|
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||
|
|
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B |
|
||
|
|
# NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 |
|
||
|
|
# NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO |
|
||
|
|
# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE.
|
||
|
|
#
|
||
|
|
# Notable bits:
|
||
|
|
# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */
|
||
|
|
# NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B */
|
||
|
|
# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */
|
||
|
|
# NFA_TECHNOLOGY_MASK_ISO15693 0x08 /* Proprietary Technology */
|
||
|
|
# NFA_TECHNOLOGY_MASK_KOVIO 0x20 /* Proprietary Technology */
|
||
|
|
# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */
|
||
|
|
# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */
|
||
|
|
POLLING_TECH_MASK=0xEF
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Force P2P to only listen for the following technology(s).
|
||
|
|
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||
|
|
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F |
|
||
|
|
# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE
|
||
|
|
#
|
||
|
|
# Notable bits:
|
||
|
|
# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */
|
||
|
|
# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */
|
||
|
|
# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */
|
||
|
|
# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */
|
||
|
|
P2P_LISTEN_TECH_MASK=0xC4
|
||
|
|
|
||
|
|
PRESERVE_STORAGE=0x01
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# NCI Hal Module name
|
||
|
|
NCI_HAL_MODULE="nfc_nci.pn54x"
|
||
|
|
|
||
|
|
##############################################################################
|
||
|
|
# Deactivate notification wait time out in seconds used in ETSI Reader mode
|
||
|
|
# 0 - Infinite wait
|
||
|
|
NFA_DM_DISC_NTF_TIMEOUT=100
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# AID_MATCHING constants
|
||
|
|
# AID_MATCHING_EXACT_ONLY 0x00
|
||
|
|
# AID_MATCHING_EXACT_OR_PREFIX 0x01
|
||
|
|
# AID_MATCHING_PREFIX_ONLY 0x02
|
||
|
|
AID_MATCHING_MODE=0x01
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Default Secure Element route id
|
||
|
|
DEFAULT_OFFHOST_ROUTE=0x02
|
||
|
|
|
||
|
|
###############################################################################
|
||
|
|
# Vendor Specific Proprietary Protocol & Discovery Configuration
|
||
|
|
# Set to 0xFF if unsupported
|
||
|
|
# byte[0] NCI_PROTOCOL_18092_ACTIVE
|
||
|
|
# byte[1] NCI_PROTOCOL_B_PRIME
|
||
|
|
# byte[2] NCI_PROTOCOL_DUAL
|
||
|
|
# byte[3] NCI_PROTOCOL_15693
|
||
|
|
# byte[4] NCI_PROTOCOL_KOVIO
|
||
|
|
# byte[5] NCI_PROTOCOL_MIFARE
|
||
|
|
# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
|
||
|
|
# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
|
||
|
|
# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
|
||
|
|
NFA_PROPRIETARY_CFG={05:FF:FF:06:81:80:70:FF:FF}
|
||
|
|
|
||
|
|
#################################################################################
|
||
|
|
# Bail out mode
|
||
|
|
# If set to 1, NFCC is using bail out mode for either Type A or Type B poll.
|
||
|
|
NFA_POLL_BAIL_OUT_MODE=0x01
|
||
|
|
#################################################################################
|